- 您现在的位置：买卖IC网 > Sheet目录350 > PCA9633BS,118 (NXP Semiconductors)IC LED DRIVER RGBA 16-HVQFN
NXP Semiconductors
PCA9633
4-bit Fm+ I 2 C-bus LED driver
7.7 Using the PCA9633 with and without external drivers
The PCA9633 LED output drivers are 5.5 V only tolerant and can sink up to 25 mA at 5 V.
If the device needs to drive LEDs to a higher voltage and/or higher current, use of an
external driver is required.
? INVRT bit (MODE2 register) can be used to keep the LED PWM control ?rmware the
same (PWMx and GRPPWM values directly calculated from their respective formulas
and the LED output state determined by LEDOUT register value) independently of the
type of external driver. This bit allows LED output polarity inversion/non-inversion only
when OE = 0.
? OUTDRV bit (MODE2 register) allows minimizing the amount of external components
required to control the external driver (N-type or P-type device).
Table 17.
Use of INVRT and OUTDRV based on connection to the LEDn outputs when OE = 0 [1]
INVRT OUTDRV Direct connection to LEDn
External N-type driver
External P-type driver
Firmware
External
Firmware
External
Firmware
External
pull-up
resistor
pull-up
resistor
pull-up
resistor
0
0
formulas and LED
output state values
LED current formulas and LED required
limiting R [2]
output state
formulas and LED
output state values
required
apply [2]
values inverted
apply
0
1
formulas and LED
LED current formulas and LED not required formulas and LED
not
output state values
apply [2]
limiting R [2]
output state
values inverted
output state values required [4]
apply [4]
1
0
formulas and LED
output state values
LED current formulas and LED required
limiting R
output state
formulas and LED
output state values
required
inverted
values apply
inverted
1
1
formulas and LED
output state values
inverted
LED current formulas and LED not
required [3]
limiting R
output state
[3]
values apply
formulas and LED
output state values
inverted
not required
[1]
[2]
[3]
[4]
OE applies to 16-pin version only. When OE = 1, LED output state is controlled only by OUTNE[1:0] bits (MODE2 register).
Correct con?guration when LEDs directly connected to the LEDn outputs (connection to V DD through current limiting resistor).
Optimum con?guration when external N-type (NPN, NMOS) driver used.
Optimum con?guration when external P-type (PNP, PMOS) driver used.
PCA9633_5
? NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 25 July 2008
18 of 43
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
PCA9634D,118
IC LED DRIVER RGBA 20-SOIC
PCA9635PW/S911,118
IC LED DRIVER RGBA 28-TSSOP
PCA9685PW,118
IC LED DRIVER RGBA 28-TSSOP
PCA9922PW,118
IC LED DRIVER LINEAR 16-TSSOP
PCA9955TW,118
IC LED DRVR CONST CURR
PCF85102C-2P/03,11
IC EEPROM 2KBIT 100KHZ 8DIP
PCF85103C-2T/00,11
IC EEPROM 2KBIT 100KHZ 8SOIC
PCF8570T/F5,512
IC SRAM 2KBIT 100KHZ 8SOIC
相关代理商/技术参数
PCA9633BS-T
功能描述:LED照明驱动器 4BIT I2C FM+ TP LED CON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633D16
功能描述:LED照明驱动器 LED DRVR 4BIT I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633D16,112
功能描述:LED照明驱动器 LED DRVR 4BIT I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633D16,118
功能描述:LED照明驱动器 4BIT I2C FM+ TP LED CON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633DEMO
功能描述:开发板和工具包 - 8051 Brd Philips PCA9633
RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压:
PCA9633DP1,118
功能描述:LED照明驱动器 LED DRVR 4BIT I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633DP1,118-CUT TAPE
制造商:NXP 功能描述:PCA9633 Series 25 mA 5.5 V 1 MHz SMT 8-bit I2C-Bus LED Driver - TSSOP-8
PCA9633DP2,118
功能描述:LED照明驱动器 4BIT I2C FM+ TP LED CON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N